Why Are My Clippers So Loud?

If you have a noisy pair of clippers, you are not alone. This problem can be caused by a couple of different things, from a worn-out armature to a blown power fuse. Here’s what you can do to prevent the problem from occurring again.

OnlySilent featured on media
Disclosure : Some of the links below are affiliate links, meaning at no additional cost, I will earn a commission if you click through and make a purchase. As an Amazon Associate, I earn from qualifying purchases.

rotary motor

If your clipper is too loud, you might have to adjust the armature. This is located on the right side of the clipper, and can be easily accessed using a small screwdriver. You need to turn the screw counter-clockwise until you can hear a quiet whirring sound. Once you’ve adjusted the armature, replace the cap.

In some clippers, the motors are not aligned properly. In this case, the motor is not getting the correct voltage. In other cases, the blades are misaligned. You can easily see whether they’re aligned correctly by looking down the length of the blades. Another common cause of clipper noise is friction. You can reduce the friction by lubricating the blades with clipper oil. However, you should note that some manufacturers don’t recommend lubricating their blades.

blade alignment

The noise made by clippers is often attributed to improper blade alignment. The blades should be slightly longer than the cutting blade and the blades’ edges should be parallel. There should also be some space between the blades. Blade misalignment can occur for a variety of reasons and is very easy to remedy. To check for blade misalignment, run a finger along the blade’s edge. If the blade is dull, it will feel rough to the touch.

READ ALSO :   Why Jets Are So Loud

You may notice the blades getting slanted when you tighten the blades. To correct this, loosen the screws that hold the blades together and move them closer together. To prevent misalignment, you should move the blades together slowly.

blown power fuse

If your clipper has been making a lot of noise lately, it might be the fault of a blown power fuse. Blocked fuses can occur for a variety of reasons, including faulty wiring, power surges, or socket overloads. You can test the power supply by trying another power outlet or changing the fuse.

worn out armature

If the armature of your clippers has worn out, it may be time to get them repaired. The motor field, also known as the motor, is made of a steel tube lined with two curved magnets. The armature spins inside this tube and causes the blade drive to move back and forth to cut the hair. Often, this component can be damaged by dropping the clipper. In this case, it may be necessary to replace the motor field, armature, and switch. These parts are not cheap. A new motor field will cost about $25 and a new switch is about $15. In addition, a labor charge may be involved.

children’s hair

The sound of a children’s hair clipper can make it hard for kids to sit still. And, it can even be distracting for adults. Not to mention that the noise it creates can be deafening in a tiny bathroom. To help combat the sound, parents can give their children sensory toys while they’re getting their hair cut.

READ ALSO :   Why is My HRV So Loud?

Parents can buy a clipper that’s water resistant, but they’ll still need to clean it, especially if they have a small child. An IPX-certified clipper is much easier to clean than a regular hair clipper. The IPX certification is designed to help make the cleaning process easier and ensure that the clipper remains in top shape. Noise from a children’s hair clipper can be caused by many different causes, including blades that aren’t oiled or a faulty motor. The head of the clipper should also be cleaned daily to ensure a quiet and effective operation.

worn out power screw

The power screw on your hair clipper is easily adjusted. If your clippers are too loud or they are not cutting your hair as well as you’d like, you may need to adjust this screw. If this is the case, you can use a screwdriver to reposition it.

First, check to see if your blades are dull. If they feel dull to you, they are likely dull. If they’re dull, you can easily test for dullness by running your finger along the edge. If it’s dull, it will feel rough.